Hydrophilicity Test Solution

Hydrophilicity Test Solution

Visually evaluates fabric wetting and water-spreading behaviour to support pretreatment efficiency, absorbency and dyeing-readiness control.

  • Practical field-use analysis
  • Supports rapid decision making
  • Reproducible and reliable results
Providing details like intended use, delivery location, packaging preference, and quantity will help us offer you faster and more accurate pricing.
Product Code: 337
Barcode: 8680131853373
Last update: 13 Ekim 2026 , Salı

Testonic Hydrophilicity Test Solution is designed for visual evaluation of wetting, water absorption and surface-spreading behaviour on cotton, viscose, modal and polyester fabrics.

The lightly coloured test solution makes it easier to observe how liquid spreads over the fabric surface and how quickly it is absorbed. This allows the product to be used not only for hydrophilicity control, but also as a practical process-control tool for comparing the actual effectiveness of desizing, washing, bleaching and other pretreatment stages on the fabric.

Control Parameter
Wetting, absorption and surface-spreading behaviour
Primary Use
Pretreatment efficiency and fabric hydrophilicity control
Process Focus
Desizing, washing, bleaching and dyeing preparation
Operational Benefit
Shows the actual effect of pretreatment on the fabric quickly and visually

Why Is Hydrophilicity Control Important?

One of the main objectives of textile pretreatment is to remove sizing materials, natural oils and waxes, process auxiliaries and other residues sufficiently so that the fabric is properly prepared for subsequent wet processes.

If the fabric does not accept water rapidly and uniformly, pretreatment may not have produced the same result across the entire material. This can lead to differences in penetration, dye uptake, chemical distribution and surface uniformity during subsequent dyeing or finishing stages.

For this reason, hydrophilicity testing is not only a measurement of a fabric property, but also an important control point for confirming the actual effectiveness of the pretreatment process on the fabric.

How Does It Show Pretreatment Efficiency?

Hydrophilicity results become particularly valuable when the same fabric is compared at different process stages or across different production lots.

Control Point Information Provided What Should Be Evaluated
Greige Fabric Shows the initial wetting and absorbency behaviour of the fabric. Effect of sizing, oils, waxes and other surface residues on pretreatment requirements.
After Desizing Shows whether the fabric's ability to accept water has improved. Desizing and washing performance.
After Bleaching Shows how effectively pretreatment has prepared the fabric surface for subsequent wet processing. Bleaching efficiency, washing and process uniformity.
Before Dyeing Helps evaluate whether the fabric is ready to accept the dye bath rapidly and uniformly. Need for additional washing or pretreatment control.

What Can Be Suspected Based on the Hydrophilicity Problem Observed?

A hydrophilicity test does not identify the chemical source of a problem on its own; however, wetting and spreading behaviour can significantly narrow the process points that should be investigated.

Observed Condition Possible Cause to Investigate First Process Interpretation
Droplet remains on the surface for a long time Insufficient desizing, oil/wax residue, synthetic polymer or other hydrophobic surface residues The fabric surface may not be accepting water sufficiently; pretreatment efficiency should be reviewed.
Some areas absorb quickly while others absorb slowly Non-uniform desizing, local oil/polymer residue or process non-uniformity Even if the fabric appears generally hydrophilic, local differences may later appear as shade non-uniformity during dyeing.
Hydrophilicity remains low after desizing Synthetic or mixed sizing residue, insufficient washing or other hydrophobic residues The investigation should not focus only on starch removal; PVA, PVAc, acrylate and other residues should also be considered.
Hydrophilicity is lower than expected after bleaching Insufficient cleaning, unsuitable process time/temperature or inadequate washing The bleaching process may have achieved the target whiteness while still failing to prepare the fabric fully for subsequent wet processing.
Different absorption times between lots Differences in raw material, sizing level or pretreatment performance It should be checked whether the same pretreatment recipe produces the same level of surface cleanliness on different lots.
Local light/dark shade variation during dyeing Local differences in absorbency and wettability Problem and unaffected areas can be compared for hydrophilicity to investigate a possible pretreatment-related cause.
Low wettability on polyester Oil, spin finish, finishing agent or other hydrophobic surface residues The naturally more hydrophobic character of polyester should also be considered while evaluating cleaning efficiency and finishing chemicals.

Which Problems Can Hydrophilicity Results Help Investigate?

Low Absorbency
Helps investigate insufficient pretreatment or residues that interfere with wet processing on the fabric surface.
Local Shade Variation
Problem areas can be compared with unaffected fabric areas to determine whether a local absorbency difference is present.
Lot-to-Lot Variation
Surface preparation and hydrophilicity performance of different fabric lots processed under the same conditions can be compared.
Pretreatment Verification
Shows whether the fabric has actually become ready for subsequent wet processes after desizing, washing and bleaching.

Why Is It Important for Evaluating Bleaching Efficiency?

Whiteness alone is not always sufficient to evaluate bleaching performance. A fabric may reach the required whiteness while hydrophobic residues or insufficiently removed process contaminants still affect its behaviour during subsequent dyeing.

For a stronger evaluation of bleaching performance, whiteness + hydrophilicity + residual hydrogen peroxide can be monitored together.

Effective bleaching is not only about achieving a whiter fabric; it is about producing a clean, uniform, hydrophilic substrate that is ready for subsequent wet processing.

What Does It Provide When Used Together with the Sizing Test?

Low or uneven wetting observed with the Hydrophilicity Test Solution shows that a problem exists, but it does not by itself identify which residue is responsible.

In this case, evaluation together with the Testonic Sizing Test Kit is particularly useful. The possible presence of starch, PVA, PVAc, CMC or acrylate-based sizing residues can be investigated, helping narrow the cause of poor hydrophilicity.

The two tests therefore complement each other: the Hydrophilicity Test Solution helps answer “Is the pretreatment result sufficient?”, while the Sizing Test Kit helps answer “Could residual sizing be the reason for insufficient hydrophilicity?”

Bleaching Control Together with the Hydrogen Peroxide Test

Hydrophilicity and residual hydrogen peroxide provide different but complementary information during bleaching control. The hydrogen peroxide test shows how the process chemistry is progressing, while the hydrophilicity test shows the actual surface behaviour of the fabric after pretreatment.

When these two parameters are monitored together with whiteness, the mill can evaluate not only “Has bleaching been completed?” but also “Has the bleaching process produced the required fabric performance efficiently and reproducibly?”

Apply pretreatment → check hydrophilicity → investigate possible residues if a problem is observed → adjust process conditions → verify again → proceed to dyeing with greater process control.

Use in Standard Test Approaches

Different standard test approaches are used to evaluate water absorbency and wettability of textile materials. The coloured formulation of the Hydrophilicity Test Solution makes the movement of liquid over the fabric surface easier to observe visually.

Reference Evaluation Area
ISO 9073-12:2007 One of the reference approaches used for evaluating liquid absorption and absorbency behaviour in textile materials.
AATCC Test Method 79 A test approach used to evaluate water absorbency and droplet absorption behaviour of textile materials.
BS 3449:1990 One of the references related to evaluating water-absorption performance of textile materials.

The test liquid and application conditions specified by the relevant standard method should be followed where formal compliance testing is required. The coloured formulation of the Testonic Hydrophilicity Test Solution is intended to make liquid spreading and absorption behaviour easier to observe during routine mill control.

Which Test Should I Choose for Textile Raw-Material and Pretreatment Control?

The parameter to be controlled in raw-material and pretreatment-related quality differences depends on the fibre type and process stage. Testonic textile control products evaluate these points in a complementary way.

Control Need Recommended Testonic Product
Sugar load and stickiness risk in raw cotton Sugar Test Kit – For Cotton
Sulfur-related residue load in raw viscose Sulfur Residue Test Kit for Viscose
Starch, PVA, PVAc, CMC or acrylate sizing structures on fabric Sizing Test Kit – Starch / PVA / PVAc / CMC / Acrylate
Hydrogen peroxide control during and after bleaching Hydrogen Peroxide Residue Test Kit for Bleaching
Fabric wettability, absorbency and pretreatment-result control Hydrophilicity Test Solution

Frequently Asked Questions

What should be considered if the fabric absorbs water slowly?
Insufficient desizing, natural oil and wax residues, synthetic polymers, process auxiliaries or other hydrophobic surface residues should be investigated. The test reveals the presence of a wetting problem; the exact cause should be determined together with other process controls.
What does it mean if some areas of the fabric wet quickly while others wet slowly?
This may indicate that pretreatment has not been uniform across the fabric. Local sizing, oil or polymer residues and differences in washing performance should be investigated.
Can whiteness be acceptable while hydrophilicity remains low after bleaching?
Yes. Whiteness and surface cleanliness are not the same parameter. The fabric may reach the target whiteness while residual hydrophobic substances or insufficient pretreatment still limit wettability.
Can hydrophilicity testing help investigate dyeing problems?
Yes. Problem areas can be compared with unaffected areas to determine whether a local absorbency difference exists. This is particularly useful when investigating poor dye uptake, light/dark shade variation and surface non-uniformity.
Which Testonic test should be used next if hydrophilicity is low?
If sizing residue is suspected, the Sizing Test Kit can be used to investigate starch, PVA, PVAc, CMC and acrylate structures. When evaluating bleaching performance, combining the result with the Hydrogen Peroxide Residue Test and whiteness data provides stronger process information.
Can different fabric lots be compared?
Yes. Under the same test conditions, the absorption and spreading behaviour of different lots can be compared to identify raw-material or pretreatment-related variation at an early stage.
Can it also be used on polyester fabric?
Yes. Considering the naturally more hydrophobic character of polyester, it can be used particularly to compare the effects of washing, spin finish, oils, finishing agents and other surface treatments.
How can the greatest value be obtained from the test result?
Recording the result together with fabric lot, process stage, desizing conditions, bleaching parameters, whiteness and actual dyeing performance helps the mill establish its own hydrophilicity and pretreatment quality profile.

For Textile Finishing and Dyeing Businesses

Analyzes the hydrophilicity properties of cotton, viscose, modal and polyester fabrics.

Test and Process Control Kits for Textile Finishing and Dyeing Mills

Checks water absorption behavior after preparation and washing, rapidly indicating desizing, degreasing and surface-preparation performance.

Testonic® Dyehouse Control Pack

Practically evaluates hydrophilicity by checking the water absorption behavior of fabric. Rapidly indicates preparation, degreasing, desizing and surface preparation performance.

Technical Documents

No technical document has been added for this product yet.
Related Posts

Related News

Technical Support and Product Consulting

You can use the form to find the most suitable chemical solution for your needs or to obtain detailed information about the technical specifications of our products.
Your requests are carefully reviewed and answered by Colin's expert team.

You can ask us about the product.

Colin Chemical Industry Inc.
We have been offering specific solutions for your scientific preferences for 26 years.

İkitelli OSB Mutsan Sanayi Sitesi M10 Blok No:3 Başakşehir İSTANBUL


© 2026 Colin Kimya San. ve Tic. A.Ş. All Rights Reserved. 216.73.216.104