Testonic® Water Purifier Control Test Kit is designed for convenient monitoring of the pre-filter, RO membrane, mineral filter and alkaline filter stages of water purification systems. Four dedicated test solutions allow you to observe possible changes in filter performance through visible color reactions.
Suitable for household reverse osmosis (RO) and multi-stage water purification systems. Its straightforward, instrument-free application makes routine filter checks and maintenance planning easier.
What Does the Kit Check?
- Pre-filter Control: Checks for residual chlorine after the pre-filter stage.
- Membrane Control: Provides a preliminary assessment of changes in membrane outlet water.
- Mineral Control: Monitors the effect of the mineral filter on treated water.
- Alkaline Control: Checks whether the final outlet water has acidic, neutral or alkaline characteristics.
3 Easy Steps
- Collect a Sample: Take a water sample from the outlet of the filter stage being checked.
- Add the Solution: Fill the test tube to the indicated level and add 3 drops of the corresponding control solution.
- Read the Result: Mix gently and interpret the resulting color using the instructions provided.
Package Contents
- Pre-filter Control Solution
- Membrane Control Solution
- Mineral Control Solution
- Alkaline Control pH Solution
- Test tube
- Instructions for use
Testonic® Water Purifier Control Test Kit is a practical color-based test set for checking four important stages of multi-stage water purification systems. It includes separate control solutions for pre-filters, the reverse osmosis (RO) membrane, the mineral filter and the alkaline filter.
Water purifier filters may gradually lose performance during use. By testing water collected after the relevant filter stages, the kit helps users identify possible changes and assess maintenance needs. The procedure is straightforward and requires no special measuring instrument.
Four Filter Control Tests
1. Pre-filter Control Solution
Used to check for residual chlorine in water collected after the pre-filter stage. A yellow or dark yellow color may indicate that chlorine reduction performance requires attention. No yellow coloration means that chlorine was not indicated in the tested sample by this method.
2. Membrane Control Solution
Used for a preliminary evaluation of water collected from the RO membrane outlet. According to the kit's color interpretation, blue or green represents the expected screening response, while red or dark red suggests a change that may require further investigation. Accurate membrane rejection performance should be verified by measuring TDS or conductivity at the membrane inlet and outlet.
3. Mineral Control Solution
Used to monitor changes in water after the mineral filter. According to the kit's interpretation, red indicates a detectable mineral filter effect, while green may suggest a reduced effect. This is not a quantitative measurement of calcium or magnesium concentration.
4. Alkaline Control pH Solution
Used to assess the general pH characteristics of the final outlet water. Green or blue indicates neutral or alkaline conditions, while yellow or orange indicates more acidic conditions. This provides a simple way to monitor the effect of the alkaline filter.
How to Use
Collect water from the outlet of the filter stage being checked. Rinse the test tube with that water and fill it to the middle mark.
Add 3 drops of the corresponding control solution and mix the sample gently.
Allow the color to develop and compare it with the instructions for the selected control solution.
Result Interpretation
| Control Stage | Expected Color | Color Requiring Attention |
|---|---|---|
| Pre-filters | No yellow color | Yellow / dark yellow |
| RO membrane | Blue / green | Red / dark red |
| Mineral filter | Red | Green |
| Alkaline filter | Green / blue | Yellow / orange |
Note: These colors are intended for preliminary interpretation according to the kit instructions. A color result alone does not confirm a filter failure or establish that a filter must be replaced.
Technical Specifications
| Test method | Visual color reaction |
| Control stages | 4 filter stages |
| Reagent dosage | 3 drops per test |
| Sample volume | Fill to the middle mark of the test tube |
| Result time | Approximately 5 minutes |
| Test capacity | Approximately 50 tests |
| Storage temperature | 8–24 °C |
Package Contents
- Pre-filter Control Solution
- Membrane Control Solution
- Mineral Control Solution
- Alkaline Control pH Solution
- Test tube
- Instructions for use
The kit is suitable for household RO system owners, water purifier service technicians, filter suppliers and maintenance personnel. Recording the initial color response after installing new filters provides a useful reference for later checks.
Important: Samples must be collected from the appropriate filter outlets. One sample from the final drinking-water tap cannot independently assess all four filter stages. This kit does not establish drinking-water safety or microbiological quality. Do not drink tested water.
Frequently Asked Questions
Yes. If the relevant sampling points are accessible, you can test each filter stage using its dedicated control solution. No specialized laboratory instrument is required.
No. The pre-filter, membrane and mineral tests require samples from their respective outlets. Final outlet water is used for the alkaline control.
It suggests that residual chlorine may be present after the pre-filter stage. The chlorine reduction performance should be checked.
No. The incoming water may contain little or no chlorine to begin with. This test provides only a chlorine-related screening result.
Not necessarily. Membrane performance should be confirmed by comparing inlet and outlet TDS or conductivity measurements before making a replacement decision.
No. It provides a visual indication of the mineral filter's effect, not a numerical measurement of calcium, magnesium or total mineral content.
No. It indicates whether the water has acidic, neutral or alkaline characteristics. A suitable pH measurement is needed for a numerical value.
An initial result can be recorded after installing new filters. Checks can then be repeated according to water consumption, incoming water quality and the manufacturer's maintenance recommendations.
Technical Documents
Related Posts
Related News
Technical Support and Product Consulting
You can use the form to find the most suitable chemical solution for your needs or to obtain detailed information about the technical specifications of our products.
Your requests are carefully reviewed and answered by Colin's expert team.
You can ask us about the product.