Dental Erosion Model Solution – Citric Acid 0.034 M (pH 3.6) is a literature-based laboratory test medium developed to create controlled acid exposure on enamel and dentin surfaces, investigate dental erosion processes, and evaluate the performance of protective or remineralizing treatments.
Its defined citric acid concentration and controlled pH help produce a comparable erosive challenge across different experimental groups. The product is suitable for studies involving enamel and dentin microhardness, surface loss, roughness, profilometry, microscopic examination and mineral release.
Its ready-to-use form reduces the need to weigh and dissolve citric acid or repeat pH adjustment before each experimental series. This helps limit variations in concentration and pH between studies.
Main Applications
- Controlled dental erosion studies on enamel and dentin
- Dental erosion–remineralization cycles
- Enamel and dentin surface-loss studies
- Microhardness and nanomechanical property measurements
- Surface roughness and profilometry studies
- SEM, optical microscopy and three-dimensional surface imaging
- Calcium and other mineral-release studies
- Evaluation of the anti-erosive performance of toothpastes and oral-care formulations
- Fluoride, remineralizing agent and protective coating studies
- Dental adhesive, fissure sealant, composite and surface-protection studies
- Controlled laboratory models representing acidic beverage exposure
- University research, academic theses and research projects
What Is the Citric Acid Dental Erosion Model?
Citric acid is one of the organic acids used in dental research to produce controlled acidic effects on enamel and dentin surfaces. In addition to the effect of low pH, interactions between citrate species and calcium can cause measurable changes in the mineral structure of dental hard tissues.
The condition of 0.034 M citric acid at pH 3.6 is one of the literature models used to investigate the initial stages of dental erosion, surface softening and the surface loss that may occur during extended exposure.
This model enables defined acid exposures to be applied under repeatable conditions. However, it does not reproduce all the acids, minerals, carbohydrates, additives and buffering properties found in actual beverages. The product is not a chemical equivalent of a particular beverage; it is a defined test medium for controlled dental erosion research.
There is no single universally accepted acid concentration, pH value or exposure time for dental erosion studies. The experimental protocol should therefore be determined according to the research objective, specimen type and intended degree of erosion.
Product Properties
| Test Medium Type | Citric acid-based dental erosion model solution |
| Citric Acid Concentration | 0.034 mol/L |
| Target pH | 3.60 ± 0.05 |
| Appearance | Clear and colourless liquid |
| Product Form | Ready-to-use laboratory solution |
| Specimen Types | Enamel, dentin and suitable dental material specimens |
| Primary Use | Controlled acid exposure, dental erosion and surface-change studies |
| Formulation Basis | Dental erosion research literature |
| Standard Status | Literature-based test medium; not an ISO, ASTM or DIN standard |
Why Choose a Ready-to-Use Dental Erosion Model Solution?
- Provides a defined citric acid concentration used in the scientific literature.
- Its controlled pH helps reduce variation between experimental groups.
- Eliminates citric acid weighing, dissolution and pH-adjustment steps.
- Provides a comparable acid-exposure medium for repeated experimental series.
- Suitable for enamel, dentin and appropriate dental material studies.
- Can be readily incorporated into erosion–remineralization cycles.
- Can be used as a complementary test medium with Klimek Artificial Saliva Solution.
- Custom packaging volumes and research-specific variants can be prepared.
Use and Experimental Considerations
The required solution volume, specimen-to-solution ratio, contact time, temperature, agitation conditions and application cycle should be determined according to the applicable research protocol. Before use, the product should be brought to the required working temperature and its appearance checked.
Erosive severity is not determined solely by pH and citric acid concentration. Contact time, temperature, agitation rate, specimen surface area, previous treatment of the specimen and solution-renewal frequency can directly influence the results.
Calcium and other components released from specimens may accumulate in the working solution during exposure. Because this can alter the effect of the solution on subsequent specimens, used solution should not be returned to the original container and should be renewed at intervals defined by the experimental plan.
In erosion–remineralization cycles, specimens may be rinsed with purified water after acid exposure and then transferred to Klimek Artificial Saliva Solution or another suitable remineralization medium, as specified by the research protocol.
Appropriate baseline measurements, blank solutions, negative controls and method controls should be included in microhardness, surface roughness, profilometry, microscopic imaging and mineral-release studies. The researcher is responsible for determining whether the exposure conditions are suitable for the intended experimental purpose.
Use with Klimek Artificial Saliva
Dental Erosion Model Solution provides the controlled erosive-exposure phase, while Klimek Artificial Saliva Solution pH 7.0 may be used, depending on the experimental plan, to provide a neutral mineral and electrolyte environment between acid applications.
Alternating use of these two products enables erosion, conditioning and remineralization processes on enamel and dentin surfaces to be investigated within controlled laboratory cycles. The number of cycles, exposure periods and solution volumes should be determined according to the relevant publication or research protocol.
Storage and Handling
- Keep the container tightly closed.
- Protect from direct sunlight and heat sources.
- Do not freeze.
- Check the appearance and homogeneity before use.
- Do not return specimen-contacted solution to the original container.
- Use clean laboratory equipment to prevent contamination during handling.
- Do not use if turbidity, precipitation, discolouration or loss of container integrity is observed.
- Follow the storage conditions and period of use stated on the product label.
Colin Quality and Technical Support
Colin Chemical applies controlled raw-material selection, traceable manufacturing and batch-based quality control to the preparation of dental research solutions. Dental Erosion Model Solution is prepared with a defined citric acid concentration, controlled pH and reproducible working conditions in mind.
Custom citric acid concentrations, pH values, packaging volumes and research-specific formulations may be prepared following technical evaluation. Colin’s technical team provides support for product selection, erosion–remineralization cycle planning and application-specific requirements.
Technical Documents
Related Posts
Related News
Technical Support and Product Consulting
You can use the form to find the most suitable chemical solution for your needs or to obtain detailed information about the technical specifications of our products.
Your requests are carefully reviewed and answered by Colin's expert team.
You can ask us about the product.